FORMLABS RIGID 10K RESIN
Basic information
- Chemical formula(s): Contains Filler (55-75%), Urethane Dimethacrylate (15-25%), Isobornyl Methacrylate (7-10%)
- Other names: Rigid 10K Resin, SLA Printer Resin
- Product Code: FLRG1001
- International Chemical Safety Card (ICSC): Multiple components - see individual ICSC cards
- Flammability: Not flammable (flash point >93.5°C)
- Description: High-strength photopolymer resin for use in Formlabs SLA 3D printers. Contains urethane dimethacrylate, isobornyl methacrylate, and filler materials for enhanced mechanical properties.
NFPA 704 (fire diamond)
- Health (blue): 1 - poses no health hazard, requires no precautions, and would offer no hazard beyond that of ordinary combustible materials.
- Flammability (red): 1 - must be pre-heated before ignition can occur (flash point >93.5°C).
- Instability–reactivity (yellow): 1 - normally stable, but can become unstable at elevated temperatures and pressures.
- Special notice (white): - - no special hazards.
Hazard statements
| Code | Phrase |
|---|---|
| H317 | may cause an allergic skin reaction |
| H411 | toxic to aquatic life with long lasting effects |
Precautionary statements
| Code | Phrase |
|---|---|
| P261 | avoid breathing dust/fume/gas/mist/vapours/spray |
| P272 | contaminated work clothing should not be allowed out of the workplace |
| P273 | avoid release to the environment |
| P280 | wear protective gloves, protective clothing and eye protection |
| P302+P352 | IF ON SKIN: wash with plenty of soap and water |
| P333+P313 | if skin irritation or rash occurs: get medical advice/attention |
| P363 | wash contaminated clothing before reuse |
| P391 | collect spillage |
| P501 | dispose of contents and container in accordance with local, regional, national, and international regulations |
Protective measures
Gloves
Based on the safety data sheet recommendations for handling photopolymer resins:
- Nitrile: very good - chemical resistant, impervious gloves recommended for handling acrylate resins.
- Butyl rubber: good - chemical resistant gloves suitable for extended contact.
- Natural latex or rubber: poor (not recommended) - not suitable for handling methacrylate compounds.
- Viton™: very good - excellent chemical resistance.
Safety goggles
- Always wear safety glasses or goggles when handling this product.
- Use eye protection equipment that has been tested and approved by recognized national standards.
- Corrective glasses are not considered safety goggles.
Clothing
- Wear chemical resistant protective clothing.
- Long sleeves and full-length pants required.
- Avoid skin contact - remove contaminated clothing immediately.
- Wash contaminated clothing before reuse.
- Do not allow contaminated work clothing out of the workplace.
Respiratory protection
- Use with adequate ventilation.
- If engineering controls do not maintain airborne concentrations below applicable limits, wear approved respirator.
- Emergency eye wash stations and safety showers should be available.
Spill management
- Evacuate unnecessary personnel and ventilate area.
- Extinguish any sources of ignition.
- Wear recommended personal protective equipment.
- Stop leak if safe to do so.
- Prevent from reaching drains, sewers and waterways.
- Contain and collect spillage and place in suitable container for disposal.
- Avoid contact with skin, eyes and clothing.
- Do not touch damaged containers or spilled material unless wearing appropriate protective clothing.
- Dispose according to local hazardous waste regulations.
Special warnings
- May cause allergic skin reaction - skin sensitization can occur, discontinue use if sensitization develops.
- Toxic to aquatic life with long lasting effects - prevent release to environment.
- Avoid exposure to light and heat - store below 38°C (100°F) away from direct sunlight.
- Incompatible with peroxides, strong oxidizing agents, alcohols, copper, and strong bases.
- Keep containers tightly closed when not in use.
- Use only in well-ventilated areas.
- Contains silica filler - avoid breathing dust.